Two-brothers-racing Ducati 900SS Manuel d'utilisateur télécharger pdf

Parts List

We recommend that this performance exhaust system be

installed by a qualified motorcycle technician. If you have

any doubts as to your ability to install this exhaust system,

please consult with your local motorcycle dealer. Read all

instructions first before starting installation. Make sure the

motorcycle and exhaust system are completely cool before

starting the installation. Also, make sure the bike is secure

on the sidestand or ideally a rear service stand during

installation. Be sure to save all stock exhaust components

for possible use later.

1. Make sure the bike is completely cool before starting the

installation. Make sure the bike is secure on the sidestand or

ideally a rear service stand.

2. Remove the stock mufflers at the passenger footpeg bracket

and where they slide into the end of each exhaust pipe.

HIGH PIPE ONLY- Remove the passenger footpeg brackets.

Attach the left and right side hanger brackets to where your

footpeg brackets used to be, using the supplied 8mm x

35mm hardware. On 1999 and later models, you will need to

relocate the stock rear turn signals or use the provided flush

mount turn signals to use the TBR high mount exhaust..

3. Slip the connector pipes onto the stock headers down

beneath the rider footpegs.

4. Place a bead of the hi-temp sealant on the outside edge of

the s-bend that goes into the canister. Slide the TBR canister

onto the end of the S-bend pipe. Wipe off the excess sealant

that will squeeze out. You can adjust the muffler position by

rotating the slip-on pipe where it meets the header. Repeat

on opposite side.

5. Carefully slide the muffler clamp over the muffler. (Note: The

stainless steel canister clamp and the name badge on the

canister come from the factory with a clear plastic protective

film. Please remove this film before operation.)

You may need to twist and turn the S-bend a little to get it in

the right place. Locate both tabs of the canister clamp out-

side of the spacer.Use the 8mm x 75mm hardware to secure

it. Leave loose for now. Repeat on opposite side.

6. Make sure everything is aligned and tighten all hardware.

Affix the connector springs to the muffler. Be sure to check

for proper clearance between the exhaust system and

swingarm.

7. Before you run the bike, clean off all fingerprints and dirt, as

any oily residue will etch the metal and become somewhat

permanent when the system gets hot. Run the bike and

enjoy. It is normal for some white smoke to appear the first

time you start the bike. This is packing/manufacturing oil from

inside the pipe burning off. Check for gaps or leaks. If you

find a leak, a little high temperature silicon sealant should fix

it. After 50 to 100 miles, recheck all fasteners for tightness.

IMPORTANT - PLEASE READ CAREFULLY

Canister Clamp Detail

Front

900SS Slip-On Instructions.qxd

Standard Mount High Mount

OE Exhaust System

Installation Instructions

Front

High Mount Standard Mount

Care & Cleaning / Warranty

Care & Cleaning

Keep system free of dirt and moisture. Store in a cool, dry place. For cleaning use a

mild spray cleaner. Always apply cleaner or polish with a soft, clean cloth.

Stainless Header System: Polished stainless steel pipes will turn a light golden hue

after a few heat cycles, this is a normal characteristic of high quality stainless steel.

Chrome Header System: Chromed header tubing will turn blue close to the exhaust

ports, this is normal. To prevent corrosion you must keep the header pipes clean.

Carbon Fiber & X-Metal Mufflers: X-Metal CF canisters will shift color from their

original silver color to an amber color after a few heat cycles, similar to the way our

stainless steel headers shift color. Always make sure the fiberglass packing inside is

in good condition and not burned out, as exhaust heat inside an empty canister will

deteriorate the Carbon Fiber / X-Metal CF sleeve. TBR sells repack kits (TBR part #

005-10038) that include new rivets and repack material as well as a drill bit (#30),

making it easy to do yourself. Also, NEVER dyno test your bike with carbon fiber muf-

flers installed - the intense heat and lack of cooling air can quickly cause the CF

material to burn. Two Brothers Racing does not provide a warranty for burned carbon

fiber.

Aluminum Mufflers: Use an aluminum or mag wheel polish such as Mother’s to

restore the bright finish to factory spec.

arranty

Two Brothers Racing products are intended for closed course competition purposes

only, and therefore are sold “as is” without warranty. Two Brothers Racing specifically

disclaims any warranties of merchantability or fitness for a particular purpose and dis-

claims all responsibility for consequential and incidental damages or any other losses

arising from the use of these products or parts.

QTY. DESCRIPTION PART NUMBER

1 MUFFLER (17.5”, LEFT EXIT) VARIES

1 MUFFLER (17.5”, RIGHT EXIT) VARIES

2 MUFFLER CLAMPS VARIES

1 STAINLESS STEEL S-BEND (PAIR) -

STANDARD MOUNT 005-1404N

HIGH MOUNT 005-1404NH

4 80MM SPRINGS 005-S80

1 HI-TEMP SEALANT 031-P22072

2 TWO BROTHERS RACING STICKERS 015-10197

STANDARD MOUNT HARDWARE KIT

2 8MM X 60MM SOCKET HEAD CAP SCREWS N/A

2 26MM SPACERS 005-S-26

2 8MM FLANGE NUTS N/A

2 8MM WASHERS N/A

HIGH MOUNT HARDWARE KIT

1 HIGH MOUNT MUFFLER HANGER BRACKET (LEFT SIDE) 005-14-11331

1 HIGH MOUNT MUFFLER HANGER BRACKET (RIGHT SIDE) 005-14-11332

2 8MM X 75MM SOCKET HEAD CAP SCREWS N/A

4 8MM X 35MM SOCKET HEAD CAP SCREWS N/A

2 34MM SPACERS 005-S-34

2 8MM FLANGE NUTS N/A

6 8MM FLAT WASHERS N/A

1 FLUSH MOUNT TURN SIGNALS (PAIR) 005-88T

Standard Mount High Mount 1

Résumé du contenu

Page 1 - Standard Mount High Mount

DDuuccaattii 77775500SSSS//990000SSSS DDuuaallSSlliipp--OOnn EExxhhaauusstt SSyysstteemmParts ListWe recommend that this performance exhau

Modèles reliés Ducati 750SS

Commentaires sur ces manuels

Pas de commentaire

Two-brothers-racing Ducati 900SS Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Two-brothers-racing Ducati 900SS. Two Brothers Racing Ducati 900SS User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés Ducati 750SS

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Two-brothers-racing Ducati 900SS