Two-brothers-racing Honda CBR1100XX Manuel d'utilisateur télécharger pdf

Parts List

IMPORTANT - PLEASE READ CAREFULLY

motorcycle technician. If you have any doubts as to your ability to install this

performance part, please consult with your local motorcycle dealer. Read all

exhaust system are completely cool before starting the installation. Also,

make sure the bike is secure on a center stand or ideally a service lift during

installation. Be sure to save all stock components for possible use later.

Installation Instructions

1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the sidestand or

ideally a service lift.

2. Remove the stock exhaust canister by removing the mounting hardware at the passenger footpeg bracket and loosening

the clamp located at the canister/header junction. Remove the stock exhaust canister at this point. Remove the OEM

gasket. This will be re-used.

3. Install the slip-on tubes using the supplied high-temp sealant and barrel clamp.

4. Install VALE adapter kit using the supplied kit instructions.

5. Place a bead of the hi-temp sealant on the outside edge of the s-bend that goes into the canister. Slide the TBR canister

onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out.

6. Carefully slide the mufﬂer clamp over the mufﬂer. (Note: The stainless steel canister clamp and the name badge on the

canister come from the factory with a clear plastic protective ﬁlm. Please remove this ﬁlm before operation.) Attach it to

the footpeg bracket using the stock hardware. Leave loose for now.

7. Make sure everything is aligned and tighten all hardware. Afﬁx the two connector springs to the mufﬂer.

8. Repeat Steps 2-6 on the opposite side.

9. Remove the side stand stop from the stock left side exhaust canister and install onto the TBR left side S-bend.

10. Before you run the bike, clean off all ﬁngerprints and dirt, as any oily residue will etch the metal and become somewhat

permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the ﬁrst time

you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you ﬁnd a

leak, a little high temperature silicon sealant should ﬁx it. After 50 to 100 miles, recheck all fasteners for tightness.

Honda

CBR1100XX

V.A.L.E.™ Dual Slip-on Exhaust System with M-2 Canister

Part # 005-680406DM, 005-680407DM, 005-680408DM, 005-680419DM, 005-680420DM

Qty. Description Part Number

2 Mufﬂer Varies

1 S-Bend Tube Set 005-68-04-N

2 Mufﬂer Clamp Varies

1 HARDWARE KIT 005-68-3

2 VALE Adapter Kit 005-2-1-V

4 80mm Extension Springs 005-S80

2 Barrel Clamp 005-27-63MSH

1 Permatex Ultra Black Gasket Maker 031-P22072

1 T20 Torx Screw Wrench 005-9-15820

1 TBR Sticker Kit 015-10212

V.A.L.E.

V ARIABL E A XIS L OCKIN G E XHAUST

Warranty

Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”

without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular

purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use

of these products or parts.

Care & Cleaning

Keep system free of dirt and moisture. Store in a cool, dry place. For cleaning use a mild spray cleaner. Always apply cleaner or polish with a soft, clean cloth.

Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality stainless

steel.

Carbon Fiber Mufﬂers: Always make sure the ﬁberglass packing inside is in good condition and not burned out, as exhaust heat inside an empty canister will

deteriorate the Carbon Fiber sleeve. TBR sells repack kits (TBR part # 005-10038) that i

nclude new rivets and repack material as well as a drill bit (#30), making

it easy to do yourself. Also, NEVER dyno test your bike with carbon ﬁber mufﬂers installed - the intense heat and lack of cooling air can quickly cause the CF

material to burn. Two Brothers Racing does not provide a warranty for burned carbon ﬁber.

Aluminum Mufﬂers: Use an aluminum or mag wheel polish such as Mother’s to restore the bright ﬁnish to factory spec.

Repack all road canisters every 3,000 miles. Part #005-10038

V.A.L.E 1

Résumé du contenu

Page 1 - V.A.L.E

Parts ListIMPORTANT - PLEASE READ CAREFULLYmotorcycle technician. If you have any doubts as to your ability to install this performance part, please c

Commentaires sur ces manuels

Pas de commentaire

Two-brothers-racing Honda CBR1100XX Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Two-brothers-racing Honda CBR1100XX. Two Brothers Racing Honda CBR1100XX User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Two-brothers-racing Honda CBR1100XX