Two-brothers-racing Honda VFR750 Manuel d'utilisateur télécharger pdf

Parts List

IMPORTANT - PLEASE READ CAREFULLY

We recommend that this performance part be installed by a qualied

motorcycle technician. If you have any doubts as to your ability to install this

performance part, please consult with your local motorcycle dealer. Read all

instructions rst before starting installation. Make sure the motorcycle and

exhaust system are completely cool before starting the installation. Also,

make sure the bike is secure on a center stand or ideally a service lift during

installation. Be sure to save all stock components for possible use later.

Installation Instructions

1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the sidestand or

ideally a rear service stand.

2. Loosen the clamp that holds the canister to the headers under the bike. Remove the hardware that holds the stock canister

at the passenger footpeg bracket. Take off the canister. Be careful to avoid damaging the round gasket, you’ll need to use it

again.

3. Install the new S-bend pipe onto the end of the header collector, reusing the stock gasket and clamp. Leave loose for now.

4. Instal VALE adapter kit using the supplied kit instructions.

5. Place a bead of the hi-temp sealant on the outside edge of the s-bend that goes into the canister. Slide the canister onto

the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out.

6. Carefully slide the canister clamp over the canister. (Note: The stainless steel canister clamp and the name badge on the

canister come from the factory with a clear plastic protective ﬁlm. Please remove this ﬁlm before operation.) You may need

to twist and turn the S-bend a little to get it in the right place. Locate both tabs of the canister clamp on the inside of the

passenger footpeg bracket. Use the stock hardware to secure it. Leave loose for now.

7. Make sure everything is aligned and tighten all hardware. Afﬁx the connector springs to the mufﬂer.

8. Be sure to allow the sealant to dry per the manufacturer’s instructions before starting the bike. Before you run the bike,

clean off all ﬁngerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the

system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the ﬁrst time you start the bike.

This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you ﬁnd a leak, a little high

temperature silicon sealant should ﬁx it. After 50 to 100 miles, recheck all fasteners for tightness.

1994-97 Honda

VFR750

V.A.L.E.™ Slip-on Exhaust System with M-2 Canister

Part # 005-360406M, 005-360407M, 005-360408M

Qty. Description Part Number

1 Mufﬂer Canister Varies

1 Canister Clamp Varies

1 Stainless Steel S-Bend Tube 005-36-10604

1 HARDWARE KIT 005-36-3

1 VALE Adapter Kit 005-2-1-V

2 80mm Swivel Hook Spring 005-S80

1 Permatex Ultra Black Gasket Maker 031-P22072

1 T20 Torx Screw Wrench 005-9-15820

1 TBR Sticker Kit 015-10212

V.A.L.E.

V A R I A B L E A X I S L O C K I N G E X H A U S T

Care & Cleaning

Keep system free of dirt and moisture. Store in a cool, dry place. For cleaning use a mild spray cleaner. Always apply cleaner or polish with a soft, clean cloth.

Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality

stainless steel.

Carbon Fiber Mufﬂers: Always make sure the ﬁberglass packing inside is in good condition and not burned out, as exhaust heat inside an empty canister will

deteriorate the Carbon Fiber sleeve. TBR sells repack kits (TBR part # 005-10038) that include new rivets and repack material as well as a drill bit (#30), making

it easy to do yourself. Also, NEVER dyno test your bike with carbon ﬁber mufﬂers installed - the intense heat and lack of cooling air can quickly cause the CF

material to burn. Two Brothers Racing does not provide a warranty for burned carbon ﬁber.

Aluminum Mufﬂers: Use an aluminum or mag wheel polish such as Mother’s to restore the bright ﬁnish to factory spec.

Repack all road canisters every 3,000 miles. Part #005-10038

Warranty

Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is” without warranty. Two Brothers Racing specifically disclaims any

warranties of merchantability or fitness for a particular purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use of these

products or parts.

V.A.L.E 1

Résumé du contenu

Page 1 - V.A.L.E

Parts ListIMPORTANT - PLEASE READ CAREFULLYWe recommend that this performance part be installed by a qualied motorcycle technician. If you

Commentaires sur ces manuels

Pas de commentaire

Two-brothers-racing Honda VFR750 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Two-brothers-racing Honda VFR750. Two Brothers Racing Honda VFR750 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Two-brothers-racing Honda VFR750