Two-brothers-racing Triumph Speed Triple Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Two-brothers-racing Triumph Speed Triple. Two Brothers Racing Triumph Speed Triple User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
V.A.L.E.
V A R I A B L E A X I S L O C K I N G E X H A U S T
TM
Parts List
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualied
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions rst before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Also,
make sure the bike is secure on a centerstand or ideally a service lift during
installation. Be sure to save all stock components for possible use later.
Installation Instructions
1. Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on a centerstand
or ideally a service lift.
2. Remove both of the rear stock slip-on assemblies.
Remove the heat shields first to allow access to the
muffler mounting bolts.
3. Loosen stock barrel clamp and remove the rear s-bend
section.
4. Slide the supplied muffler canister clamp over the muffler
canister.
5. Slide the X-Lite ring over the TBR slip-on tube. Use
the 4 (four) 6 x 14mm socket head cap screws and
split lock washers to loosely attach the X-Lite ring
to the TBR muffler inlet (see below).
6. Now that the s-bend and muffler are ready to be installed,
insert the s-bend tube into the stock headpipe.
7. Loosely attach muffler assembly to the bike, using the
supplied spacer and hardware. Finger tighten only.
8. Position s-bend so that it clears on all sides and then
tighten bottom clamp.
9. Make sure position of muffler is correct. Once you are
satisfied with its position, tighten X-Lite ring bolts on
the V.A.L.E.
TM
assembly.
10. Tighten the muffler clamp, securely attaching the muffler
assembly to the bike.
11. Double check your work to ensure everything has been
tightened and is properly installed.
12. Before you run the bike, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run
the bike and enjoy. It is normal for some white smoke to
appear the first time you start the bike. This is packing/
manufacturing oil from inside the pipe burning off. Check
for gaps or leaks. If you find a leak, a little high temperature
silicon sealant should fix it. After 50 to 100 miles, recheck
all fasteners for tightness.
2007-09 Triumph
SPEED TRIPLE
V.A.L.E. Slip-on Exhaust System
Part # 005-2320406V / 005-2320407V / 005-2320408V
Qty. Description Part Number
1 Muffler Canister Varies
1 Muffler Canister Clamp Varies
1 Slip-On Tube 005-23201S
1 HARDWARE KIT 005-232-3
1 X-Ring 005-7-2-2
1 8x85mm Socket Head Cap Screw 005-SH885
1 8mm Flat Washer 005-WF8
1 34mm Aluminum Spacer 005-S-34
1 5mm Long Handle Ball End Hex Key 005-9-18610
1 T20 Torx Screw Hex Key 005-9-15820
4 6x14mm Socket Head Cap Screw 005-SH614
4 M6 Split Lock Washer 005-WL6
1 TBR Sticker Kit 015-10212
Vue de la page 0
1 2

Résumé du contenu

Page 1 - V.A.L.E

V.A.L.E.V A R I A B L E A X I S L O C K I N G E X H A U S TTMParts ListIMPORTANT - PLEASE READ CAREFULLYWe recommend that this performance

Page 2

005-2320407V005-2320406V 005-2320408VQty. Description Part Number1 Muffler Canister M-2 Aluminum 005-232-206V1 Muffler Canister Clamp 005-2C1 Sli

Commentaires sur ces manuels

Pas de commentaire